frp sheet

FRP sheet is an amorphous, odorless, non-toxic, highly transparent colorless or slightly yellow thermoplastic engineering plastic, among which the plastic industry with a thickness of 0.25mm to 1.5mm is called a sheet.

  FRP sheets are widely used, mainly in machinery, electronics, automobiles, construction, daily necessities and other fields, and generally have the following characteristics:

         1: It has excellent physical and mechanical properties.

2: Excellent impact resistance, high tensile strength, bending strength and compressive strength; small creep and stable size.

FRP sheet manufacturers

3: It has good heat resistance up to 125 degrees and low temperature resistance of minus 45 degrees. It has stable mechanical properties, dimensional stability, electrical properties and flame retardancy in a wide temperature range. It can be used at -60~120 °C Long-term use under the environment; no obvious melting point, it is in a molten state at 220-230 ° C; due to the high rigidity of the molecular chain, the resin melt has a high viscosity.

4: Small water absorption, small shrinkage, high dimensional accuracy, good dimensional stability, low air permeability of the film; it is a self-extinguishing material;

5: Stable to light, but not resistant to ultraviolet light, good weather resistance; oil resistant, acid resistant, not resistant to strong alkali, oxidizing acid and amines, ketones, soluble in chlorinated hydrocarbons and aromatic solvents, easily caused by long-term exposure to water Hydrolysis and cracking, the disadvantage is that it is prone to stress cracking due to poor fatigue resistance, poor solvent resistance, and poor wear resistance.

We mainly produce frp film and frp sheet, if you have any questions, please feel free to contact us. We are looking forward to your visit.

What are the four elements that a glass fiber reinforced plastic sign should have?

 FRP signs should have four elements: strong reflective film adhesion, strong wind load resistance, aging resistance, and low cost.

Reflective film adhesion function, resin and curing agent are produced by the reaction of resin and curing agent in a high-temperature oven. The FRP glass fiber reinforced plastic is integrally formed. The cycle is short, the cost is low, and the thickness control is standardized.

FRP signs have good impact resistance.

FRP signs have the characteristics of corrosion resistance, aging resistance, impact resistance, flame retardancy and strong insulation.

FRP signs are resistant to water, gasoline, alcohol, electrolytic salts, acetic acid, hydrochloric acid, sodium potassium compounds, urine and asphalt.

FRP signs are suitable for long-term use in various natural environments.

FRP signs are light in texture, and the weight of 1 square meter FRP signs is only 1.5kg, which is convenient for transportation and simple construction.

The service life of FRP signs can reach more than 30 years, without any recycling value, and anti-theft.

FRP sheet manufacturers, is a high-paying technical enterprise dedicated to the development, design, production and sales of new composite materials, specializing in the research and development and production of FRP sheets, including FRP tiles, FRP flat sheets, FRP sandwich composite sheet insulation materials, products High quality, widely used in professional products such as FRP signs, special boards for passenger cars, special boards for refrigerated cars, special boards for cooling towers, special boards for construction and home furnishing, and photovoltaics.

Every product of Guangdong Yinuo Composite Materials Co., Ltd. must go through strict quality control, from raw material selection, process control, pre-shipment quality inspection and other procedures to protect the rights and interests of customers, in order to provide each customer with the best High-quality and safe products bring customers solutions with higher added value.

If you need more information about the performance of FRP flat panels, please contact our staff.

What is the difference between APET and GAG sheets?

 Many friends may not know much about the main differences between APET and GAG sheets. In fact, we can learn from many places. Here we will also introduce the relevant content to you. If you are interested in this content If you're interested, you should check it out.

What is the difference between APET and GAG sheets?

1. GAG is a three-layer composite sheet. It is a three-layer composite sheet produced by the co-extrusion of the middle layer APET and the upper and lower layers of PETG raw materials in an appropriate proportion. It is especially suitable for packaging boxes that need to be bonded by high-frequency heat sealing and glue. Its advantages are as follows:

1. Good transparency, the transparency can reach more than 90%, good texture, suitable for products requiring high transparency.

2. Excellent impact resistance and rigidity, the material is hard and durable, suitable for applications with high impact resistance.

3. Excellent processability. It can be processed by sawing, die-cutting, drilling and laser cutting. It can also be cold-formed and hot-formed, adhered, welded and polished, printed and painted; and cold-formed without whitening, the appearance is bright.

4. Good thermoformability, can be formed without preheating, high precision, shrinkage rate is about 0.5%; good deep formability, no cracking and uniform thickness.

5. Excellent food hygiene, the material is PETG, which can meet all major food regulations.

2. Compared with the widely used PVC film, A-PET (polyethylene terephthalate) sheet has the following advantages:

metal roofing companies

1. High strength: The strength of PET film is more than 20% higher than that of PVC film. It has better low temperature impact resistance and can withstand -40°C without brittle cracking. Therefore, films that are 10% thinner than PVC are usually used to replace PVC.

2. Good folding resistance: PET film does not have self-crack creases like PVC, and is more suitable for surface decoration such as documents.

3.

PET film has high transparency (PVC film is bluish), especially the gloss is better than PVC film, which is more suitable for exquisite packaging. PET products have no pollution, no crystal points, high transparency, good smoothness, and strong impact resistance. They can be widely used in exquisite packaging such as blisters, folding boxes, cylinders, and various printing windows, and can produce various types according to customer requirements. color film.

metal roofing suppliers

(1) APET transparent sheet APET film sheet: Transparent and smooth APET ordinary sheet, suitable for folding boxes, printing, and blistering.

(2) Antistatic sheet

Divided into three categories, with different levels of antistatic index, suitable for packaging of electronic products with different needs. Class A: using inner injection technology. Antistatic index: 109~1011B category: using coating technology. The antistatic index is: 109~1011C category: using coating technology. Antistatic index: 108~1010

(3) APET conductive sheets are used for electronic product packaging and turnover boxes, inner trays, outer packaging, etc.

(4) APET color sheets are transparent or opaque sheets of various colors, suitable for high-demand packaging of cosmetics and food.

Roofing Sheet manufacturers

(5) After the APET flat sheet is formed, use a precision cutting machine to cut it into APET flat sheets that meet the required size.

(6) APET laminated sheet After the APET extruded sheet is formed, it is immediately covered with a transparent protective film. It can be single-sided or double-sided. It is suitable for packaging or printing with high requirements on the surface of the sheet.

(7) APET anti-UV sheet UV means ultraviolet rays, and UV-resistant APET sheets. The product has been tested by relevant national agencies and meets the requirements for UV resistance.

What are the main characteristics of PET sheet?

 Do we feel some usefulness of PET sheet when we usually use it? Here I will introduce it to you from several aspects. This is a sheet that is commonly used in our production and life. The effect of specific use Here is an introduction for everyone, come and see if you are interested!

What are the main characteristics of PET sheet?

First, the transparency and smoothness are excellent, and the effect is very good

Second, the surface decoration performance is excellent, it can be printed without surface treatment, it is easy to suppress patterns, and it is easy to metallize.

metal roofing companies

Third, it has good mechanical strength.

Four, good chemical resistance, can withstand the erosion of various chemical substances

Five, the barrier performance of oxygen and water vapor is good

Roofing Sheet suppliers

6. Coated with polymer conductive polymer, the surface resistivity is low, the performance is stable, and it is not affected by the ambient temperature.

FRP sheet manufacturers

This is the main feature of the PET sheet introduced to you. After we introduce it to you, I believe it will give you some understanding of it! If there are customers and friends who need to buy APET sheet, GAG sheet, For ABS sheet, you can call us directly!

What are the characteristics of ABS sheet? Why choose ABS sheet? Let's take a look together!

 As an emerging material in the board industry, ABS board has been playing a good role. And it is also a very popular polymer. It can be said to be organic and artistic for the unity of materials, and it has many advantages. But in fact, many friends don't know much about the characteristics of ABS boards, especially those who are not engaged in the board industry, and don't know how to choose. Today, the editor will come to take a look at the characteristics and selection methods of ABS with you, continue to read!

metal roofing companies

1. The ABS sheet has excellent mechanical properties, its impact strength is relatively good, and it can be used at a relatively low temperature; ABS has excellent wear resistance, good dimensional stability, and oil resistance, and can be used under medium load and speed. bearings. The creep resistance of ABS is larger than that of PSF and PC, but smaller than that of PA and POM. The flexural strength and compressive strength of ABS are the poorest among plastics. The mechanical properties of ABS are greatly affected by temperature.

2. ABS board is not affected by water, inorganic salt, alkali and various acids, but it is soluble in ketones, aldehydes and chlorinated hydrocarbons. It will cause stress cracking when it is corroded by glacial acetic acid and vegetable oil. The weather resistance of ABS is poor, and it is easy to degrade under the action of ultraviolet light; after half a year outdoors, the impact strength drops by half.

FRP sheet manufacturers

3. The thermal deformation temperature of the ABS sheet is 93~118°C, and the product can be increased by about 10°C after annealing. ABS can still show certain toughness at -40°C, and can be used in the temperature range of -40~100°C. Among them, the transparency of the transparent ABS board is very good, and the grinding and polishing effect is relatively good. It is a material that can replace the PC board. Compared with acrylic, its toughness is very good, which can satisfy the meticulous processing of products.

The above are the characteristics of ABS boards. If you have needs for sheet materials, please call us Zhejiang Zhongsheng New Material Co., Ltd., and we will serve you wholeheartedly!

Analysis of common production problems of PVC sheet

 Nowadays, with the rapid development of science and technology, new developments have emerged in the building materials industry and flooring. PVC flooring has added new members to the flooring family. As a product of the high-tech era, it is characterized by green environmental protection, low cost and high cost performance. PVC transparent sheet is one of the main types of hard PVC conical twin-screw extrusion production. Common problems in the production process include: air bubbles, many crystal points, yellowish color of the sheet, etc. Below, the editor will give you a detailed introduction to the causes and solutions of the yellowing of the sheet.

1. Reasons for sheet yellowing:

metal roofing suppliers

1. The stability of PVC itself is poor.

If it was just replaced. PVC may be the resin manufacturer's own poor stability of PVC, you can try to replace PVC. However, even for the brands that have been used, even if it is PVC, it is possible that the PVC resin itself is produced by the same manufacturer, because even if it is PVC, the quality of different batches may vary.

2. Insufficient stabilizer

If there is a problem with the temperature controller, the displayed temperature is lower than the actual temperature. If the temperature is too high, the PVC will decompose and turn yellow. At this point, a more accurate temperature controller needs to be rechecked. This method is simple, and it is more accurate to use a mercury thermometer. In actual production, there is a gap between the displayed temperature of the temperature controller and the actual temperature.

PVC sheet suppliers

2. Reasons for small air bubbles in the sheet:

1. There is too much moisture in the PVC raw material. For example, in the rainy summer day, the raw material is damp, that is, the moisture may not be completely discharged from the barrel, and it will expand when heated, and then generate air bubbles in the sheet.

2. In addition, the water content of additives may be too high.

In summary, the solution can be adopted: Properly increase the mixing time of the hot mixer, and use a cooling mixer. Can effectively remove moisture from raw materials.

3 The number of crystal points in the sheet exceeds the standard, also known as fisheye

Some common causes of crystal points are: PVC resin particles are not plasticized, or the plasticization is not good. The reasons for this are: the quality of PVC resin itself is not good.

FRP sheet manufacturers

3. Under the condition of not replacing the PVC resin, the solution is as follows:

1. Appropriately increase the mixing time and increase the mixing temperature to promote the absorption of additives. And choose a high-quality mixing unit, the preforming effect of the mixing unit on the material is irreplaceable.

2. The mixed raw materials can be left for half a day or a day, let it mature, and then used.

3. It is possible to properly increase the set temperature of the barrel, increase the screw speed, increase the head pressure, etc., to further improve the plasticizing performance.

4. In terms of formulation, we must carefully select the appropriate additives and the amount of additives. At present, the additive market is chaotic and the quality of products varies widely. We should choose carefully and find a better balance between price and performance.

The above is all the content shared today, I hope it will be helpful to everyone!

How long is the service life of FRP tiles

 The service life of FRP lighting tiles is more than 15 years. We guarantee the quality of lighting tiles for 15 years. If you tell the customer service that you need a product warranty, you can send it together with the goods, so that customers can buy with more confidence.

 

FRP sheet manufacturers lighting tile is also called FRP glass fiber lighting tile, frp lighting tile can be used for several years not by glass fiber, but by unsaturated reinforced resin, the better the resin, the better the transparency, the transparency is up to 70%, Good weather resistance, no yellowing, regular transparent color, other colors need a certain amount to be produced.

Metal roofing suppliers have rich experience in producing FRP tiles, and the quality is guaranteed. They can open molds according to the models required by customers, and the thickness, color and length can be customized. Welcome to buy.

How to choose high-quality sun tiles

 Sunshine tile is a kind of board, some of its properties are almost comparable to glass, whether it is gloss or transparency, the similarity rate can reach 90%. But this material is not as fragile as glass, so how to choose high-quality solar tiles without being routinely used by manufacturers? Mingyuan Xiaobian will answer you through this article.

metal roofing manufacturers

High-quality lighting panels should be strictly controlled through layers of checks from production equipment, process technology, to raw materials.

Features of high-quality solar tiles:

The appearance of the sun tile is bright, without obvious bubbles or cracks;

The thickness of the section is uniform, and the tile type and the steel tile are the same;

FRP sheet suppliers

Long-term use without discoloration and yellowing;

Sunshine tiles have good durability, and there is no cracking phenomenon when roofing equipment is nailed;

The light transmittance is good, the light is scattered, the light is soft, and there is no dazzling feeling;

The thermal expansion coefficient of high-quality solar tiles is close to that of steel tiles, and there will be no water leakage due to thermal expansion and contraction at the nailed place.

Roofing Sheet suppliers

Characteristics of defective sun tiles:

The surface is uneven, and because of cutting corners, the thickness of the produced product is not uniform, and there are obvious air bubbles and snowflake-like cracks in Songhuajing color, which will seriously affect the lighting effect;

In addition, the section thickness of inferior solar tiles is different, the four sides of the section are thick and the center is thin, and the hand feel is very poor. When installing solar tiles, it is easy to cause accidents of stepping on air, which brings great harm to us;

In addition, the transparency of inferior solar tiles is very poor, so the life of the solar tiles produced will be very short, and the use effect will drop sharply;

In addition, inferior solar tiles have poor durability and are easy to split, which may cause rain leakage.

When choosing solar tiles, you should consider many aspects, and you can’t buy them at will because you are greedy for cheap. Once you buy defective solar tiles, it will cause roof leakage and other phenomena in the later period of use. The huge economic losses and manpower and material resources for repairs will cost you Small things lose big.

Features and functions of FRP tiles

 FRP tile is a high-quality plastic composite material with smooth surface, bright and transparent, no cracks and bubbles, uniform color, acid resistance, alkali resistance, corrosion resistance, anti-corrosion engineering, tensile strength, anti-aging, and good light transmission. Long service life and other characteristics, widely used in electronics, chemistry, pharmaceuticals, food factories, clothing factories, work paths, various work desktops on mechanical surfaces, etc.

metal roofing contractors

We are not very unfamiliar with transparent panels, but we are not very clear about the characteristics of PVC panels and what PVC panels are. The following editor will give you a detailed introduction to PVC transparent panels. Hardness panels: this PVC panel The quality of the product is first-class, the color is generally gray and white, and pvc colorful hard board can also be produced according to customer needs. The color is bright and beautiful. High hardness, high strength, high strength, UV protection (aging resistance), fire resistance and flame retardant (self-extinguishing), reliable insulation performance, bright and flat surface, no water absorption, no deformation, and easy processing. This product is an excellent thermoforming material, which can replace part of stainless steel and other corrosion-resistant composite materials, and is widely used in chemical industry, petroleum, electroplating, water purification treatment equipment, environmental protection equipment, mining, medicine, electronics, communication and decoration, etc. .

〉FRP sheet manufacturers

PVC hard board has the advantages of cold resistance, heat resistance, anti-aging, flame retardant, insulation, corrosion resistance, impact resistance, etc., and is widely used in processing and welding projects.

Roofing Material manufacturers

the

U-PVC hard board: select high-quality materials and additives, scientifically mix and extrude, low filling (density: 1.45-1.55) has excellent acid resistance, alkali resistance and corrosion resistance. CPVC hard board: high temperature resistance, can maintain sufficient strength when it does not exceed 100 ℃, has extremely low thermal conductivity, and can be used to make chemical and corrosion resistant chemical equipment.

How to insulate the FRP tiled house

 FRP tiles are favored by more and more people because of their large appearance, but FRP tiles conduct heat quickly in summer. If there are no other ways to reduce heat, it will be a steamer, so you only need to know How to effectively insulate FRP tiles can make it more comfortable when decorating and living.

        metal roofing companies

1. Profiles of heat-insulating FRP tiles

First of all, in the selection of heat-insulating FRP tile profiles, we should choose heat-insulating and sound-insulating broken bridge aluminum profiles, and cooperate with low-e hollow tempered glass, which can effectively block the invasion of outdoor temperature and block ultraviolet rays and radiation. sound insulation.

2. Heat-insulating FRP tiled roof equipment sunshade

In fact, the sunshades of FRP tile-roofed houses are like the doors and windows of our usual homes. In order to avoid direct sunlight glare, they can also reduce the temperature of the sun and achieve the purpose of sun protection and heat insulation. It can not only insulate heat but also reduce the direct focus of sunlight on us .

3. The heat-insulated FRP tiled roof can be covered with film for sun protection

Of course, the glass of the FRP tiled house is the same as the glass of the car. We can put a layer of film on the glass to fundamentally solve the problem of excessive temperature in the FRP tiled house. feature.

4. The heat-insulated FRP tile house can open the skylight to cool down

Assuming that the hot air in the sunshine room is relatively strong and surrounds the top, we can open the skylight properly first. When the skylight on the sun roof is opened, the heat will run up and out of the skylight, and then we can open it. The air conditioner is off.

5. Install sprinkler system to cool down in heat-insulated sunlight room

In the hot summer, if we want to cool down quickly, we might as well try spraying water to take away the heat from the FRP tiled house objects to cool down. It can also achieve the function of automatically cleaning the glass top surface of the sun room.

6. Air-conditioning and refrigeration of equipment in FRP tile-roofed houses

FRP sheet manufacturers mentioned the air conditioner above. In fact, the air conditioner can cool the FRP tiled house in summer and heat it in winter. The method of direct cooling can solve the problem of high temperature in the sun room in summer. As mentioned earlier, the method of insulating the sun room with so many heat insulation can only be used for most of the houses. It solves the problem of cooling, but if you want to completely cool down, you still need to install air-conditioning and cooling. Now that the living standards are improving, more and more people are installing air-conditioning in their houses, and FRP tiles can actually do it.

Using FRP tiles is the right choice

 Before you choose whether to use new FRP tile building materials, do market research in advance and whether the product function is suitable for your own use. Even if the perfect thing is not suitable for the place you use, it is not suitable. I believe that if you want to use it on the factory roof now. FRP tiles are widely used as one of the building materials for walls, heat preservation rooms for a large number of agricultural vegetable and fruit greenhouses, and roofs for gymnasiums.

metal roofing suppliers Now let's think back to our early FRP tiles. The light of FRP tiles is mainly in the form of astigmatism, which is relatively uniform and soft, and the light transmittance effect is good. FRP tiles will not produce droplet phenomenon. It has a strong resistance to saline and alkali. It has strong corrosion resistance and is used in pollution. It is also very suitable for enterprises. For example, it is a good choice for the workshop of chemical plants. It is anti-ultraviolet and has a very stable function, not easy to deform, aging or cracking. The neat and atmospheric appearance is also easy to clean, because it has a film on the surface, and the function of the film prevents dust and sewage from sticking to it, and it will be washed away directly with rain, snow, or wind, as long as the product remains within its expected period of time. There will be no other changes, no special care is required, and it is very convenient to install or disassemble and clean.

FRP sheet manufacturers In this way, the anti-corrosion function of our FRP tiles is worth mentioning. Not only is the anti-corrosion function extremely strong, but the non-polluting materials also have environmental protection functions. There are also many advantages in functions. When you buy FRP tiles, you must choose the right product so that you can buy a suitable FRP tile and use it with ease. We also welcome people who need it to come to Roofing Material suppliers for consultation.

What are the benefits of diffuse frp lighting panels

 The biggest feature of the frp lighting board is that the light transmission and scattering rate is as high as 92%, and the light transmittance is as high as 94%. We use a specially formulated resin to make the lighting board have such a function. The frp daylighting panel greatly improves the light environment of the factory or warehouse. After the light passes through the frp daylighting panel, it will not converge in one line, eliminating the light band, so that the light spreads to every corner of the building, and the light is uniform, which is energy-saving and environmentally friendly. green.

     Roofing Material suppliers

Under the light band generated by the use of ordinary FRP boards, the light energy is too concentrated, and the stored products are prone to discoloration and deterioration. The light band is too hot for people to work, and the light is very dazzling. We have encountered many owners who need the lighting panels to be as bright as possible, but in summer they use sunshade film or paint to cover the lighting panels because of too much heat. Using diffuse lighting panels can completely solve this problem.

      metal roofing suppliers

Under normal conditions, the intensity of direct radiation is 4 to 7 times that of diffuse radiation, and the lighting board mainly uses direct light. The outdoor direct radiation is reflected by the lighting panel to the indoor ceiling through the small upper window opening, and through the scattered reflection of the ceiling, it uniformly illuminates a distance away from the window.

In the case of the same window area, the place far away from the window is fully illuminated, which improves the uniformity of indoor lighting and improves visual comfort; the area of the upper opening is small, although reflected radiation enters, but it will not Severely increase the indoor air-conditioning load; and the outdoor daylighting panels play the role of external sunshade to a certain extent, which is conducive to improving the thermal comfort near the windows and reducing the air-conditioning load and direct glare.

Through the above analysis, we must have fully understood the advantages of diffuse lighting panels, and these advantages are really the reasons why solar tile manufacturers recommend it.

Reasons why anti-corrosion tiles are popular

 Technical knowledge of the product and a passion for home specific program development. Can assist with new builds, renovations, extensions and room modifications. The collection caters to a wide range of styles, including contemporary, eclectic, minimal, classic and depressed, industrial, transitional and heritage union and everything in between; there is always something to fit.

FRP sheet manufacturers

From preventive maintenance to leak corrections and even complete roof repairs, we can do any tiled roof repair on the Sunshine Coast.

Anti-corrosion tiles are special anti-corrosion materials for industrial workshop roofs. The advantages of anti-corrosion tile manufacturers: corrosion resistance, flame retardancy, no rust and water leakage; it is often used in severe corrosion of new chemical plants and replacement of old color steel roofs.

Anti-corrosion tiles are a one-stop supplier of heavy-corrosion building materials industrial plants; supply anti-corrosion tiles to ensure the corrosion index of roofs and walls.

The surface of the anti-corrosion coating has weather resistance, is more resistant to high temperature corrosion than ordinary transparent boards, and has anti-aging functions; color and decoration, milky white), reflects the decorative effect of the entire roof, and is an ideal choice for severe corrosion projects that change gray images.

The advantages of tile anti-corrosion function are: 1. Corrosion resistance, aging resistance and long service life. 2. Especially anti-corrosion, heat insulation function, 3. Low installation cost. There is no need to reserve a shrinkage cavity for installation, and the borehole is directly fixed, which is convenient and quick. There are no follow-up maintenance fees. 4. Anti-corrosion and flame retardant. The anti-corrosion tile manufacturer has strong flame retardancy, its oxygen index is > 30, reaches the secondary flame retardant standard, and burns without dripping. 5. Anti-corrosion tiles are windproof and earthquake-resistant - strong wind pressure and heavy snow pressure.

Metal roofing suppliers have super durability, chemical corrosion resistance, heat resistance, heat distortion temperature of 91 ℃, stable color, rich color, bright luster.

ASA, a synthetic resin tile application: mainly used for flat slopes, villas, garden pavilion roofs, etc.

Second, product specifications:

Thickness: 2.0mm 2.5mm 3.0mm Length: according to customized multiples

Color: customizable

Waveform: total width: 1050mm width: 960mm; wave pitch: 160mm; height: 30mm; spacing: 220mm

Three, product features:

1. Durable color:

The surface material of ASA synthetic resin tile is made of imported high weather resistance engineering resin. In the natural environment with special durability, even if it is exposed to ultraviolet rays, moisture, heat, and cold conditions for a long time, it can still maintain its color stability.

Will fiberglass tiles produce chromatic aberration?

 As a kind of polymer material, resin is a complex of various long-chain polymer compounds. The policy planning can only be measured microscopically based on gel time, viscosity, acid value, exothermic peak, etc. The products of different manufacturers are in the market. If there are obvious differences in the application characteristics, even if it is the product of the same manufacturer, the color between different batches will inevitably vary. Moreover, when the actual production line is produced, the production control environment is different, and the products produced will also be different. Therefore, there will be color difference in transparent tiles and FRP anti-corrosion tiles produced by different batches or different PVC sheet manufacturers resins. At the same time, among all the colors of FRP anti-corrosion tiles, the external environment has a particularly sensitive influence on protein color and dark blue.

metal roofing suppliers So in summary, the following conclusions can be drawn:

1. FRP anti-corrosion tiles produced in different sections, the same brand (using the same ratio, the same type of resin from the same manufacturer), and the same color will have a certain degree of color difference, or even a large color difference (the longer the distance, the greater the difference may be) ).

2. There are obvious color differences between different brands, and there will be a little color difference when using resins from different manufacturers for the same brand.

3. The color difference between retardant resins, especially secondary retardant resins, and ordinary resins will be fairly obvious.

Application and characteristics of PVC plastic steel tile

 PVC plastic-steel tiles are widely used in factories, workshops, warehouses, residences, carports, farmers' markets, road hoardings, etc., especially for ceramic production workshops, fertilizer warehouses, galvanizing plants, aluminum plants, chemical plants, etc. sex work.

Product features of PVC sheet manufacturers plastic steel tiles:

1. PVC plastic-steel tiles are acid-resistant, alkali-resistant, corrosion-resistant, and have a service life of 30 years

2. Impact resistance, stretch resistance, fire prevention, low noise, and UV resistance.

3. PVC plastic-steel tiles are beautiful and colorful in color, do not fade, do not contain asbestos components, and are a new type of environmentally friendly material.

4. Simple installation and low transportation cost.

Reasons and measures for water leakage of frp tiles

 The frp tile roof uses the water collection tank as the indoor drainage system, and the planning between the frp tile roof and the water collection tank does not have a clear leak-proof method; at the same time, it is bound by the span of the bottom steel beams, and the water collection tank needs to be installed in sections between the steel beams, while There is no special anti-leakage method proposed between the sump and the steel beam.

The upper part of the glass sloped roof is planned to be directly connected to the main structure, and only silicone weather-resistant adhesive is used as the surface layer for waterproofing. However, the unsatisfactory bonding effect between the weather-resistant adhesive and the structural surface layer will directly lead to leakage at the glass layer.

      metal roofing suppliers

The connection between the steel beams at both ends of the glass sloping roof and the wall, and the planning between the steel beams at both ends of the glass sloping roof and the lower wall are treated with weather-resistant adhesive as an anti-leakage treatment method, but the distance between the weather-resistant adhesive and the plastered surface of the wall The bonding effect is limited, so the leakage of this part is serious when inspected in the dry season.

In order to avoid the sliding of the glass on the inclined roof, the plan requires that an aluminum alloy cover plate be added to the vertical joint of the two glasses (that is, the top of the weather-resistant rubber), and the waterproof screw is used to connect the lower aluminum profile. The safety problem is solved, but the leakage of water is increased. possibility.

     Roofing Material suppliers

Before applying sealant between two glasses or between glass and steel beams, the contact surface should be completely dedusted to ensure the quality of the sealant. However, this key link is easily overlooked during construction, resulting in incomplete sealing of the colloid. , showing leakage.

Insufficient treatment of details between the water collection tank and the glass, and between the water collection tank and adjacent steel beams is another important link that constitutes leakage.

Anti-leakage method

1) Before applying the sealant, use a cloth filled with detergent to clean the contact surfaces of the glass ends and steel beams that are in contact with the colloid, and then dry the surface with a second piece of clean cloth, and require the workers to seal the sealant within 1 hour. Seal the equipment; the room between the two layers of sealant should also be cleaned with a cleaning rag.

2) During equipment construction, the glue between the glass and the glass must be full, and the thickness of the cushion glue should not be less than 35mm; the upper aluminum gland is connected with waterproof screws and the bottom aluminum alloy grid strip, and the two ends of the gland are in contact with the glass with sealant Water repellent treatment is carried out.

3) For the connection between the glass and the steel beam, the sealant is first expanded into a circular arc on one side of the steel beam to avoid partial water accumulation and aging of the sealing material.

4) The connecting part between the glass and the sump, that is, the turning point of the aluminum-plastic panel and the connecting part of the glass and the aluminum-plastic panel, add cross braces under it, so as to ensure that the connecting part has sufficient strength and facilitate future repairs.

5) For the connection between the glass and the upper concrete beam, when the concrete beam is plastered, a cement mortar groove is made at the corresponding part of the glue, and the upper part is made of dripping water, so that the colloid can be injected into the plaster layer and closely connected with the concrete bottom layer, and then The joints of cemented concrete are made into circular arcs, so as to enhance the waterproof effect.

6) For the connection between the sump and the exposed steel beam, use thin steel plates of the same material as the sump to weld with the steel beam and the sump respectively, and make a 10% flow slope to ensure smooth water flow and avoid stagnant water.

FRP sheet manufacturers

7) For the connection between the aluminum-plastic panel and the glass and the wall below the roof, except for adding steel cross braces at the bend of the aluminum-plastic panel and the bottom of the glass joint, the aluminum-plastic panel is required to extend into the plastered surface of the wall Below 10cm, the surface seam between the two is caulked with silicone weather-resistant adhesive.

8) The joints between the I-beams at both ends of the glass sloping roof and the lower wall shall be built with bricks to the bottom 5cm of the steel beams, and the top surface shall be plastered with waterproof mortar to form an outward slope. The gap between them is then sealed with construction ointment.

Flour fishing bait for silver carp and bighead carp

 Bait formula for fishing silver carp and bighead carp with hand rod:

One part of flour for fishing silver carp and bighead carp bait for north and south fishing, one part of snowflake potato powder, and an appropriate amount of strawberry essence. After mixing well, add appropriate amount of water and stir well quickly. Be careful not to rub, otherwise it will affect the atomization effect and cause poor fish gathering effect.

fish hook

The specific fishing method is double-hook floating fishing with a hook distance of about 2 cm. When fishing, the upper hook is hung with big food, and the lower hook is directly empty (the fish in the lower hook). After sinking into the bottom of the water, you can’t see it), and then lift the rod to catch silver carp and bighead carp bait in the fish flour.

Attention should be paid to the bait formula for fishing silver carp with this hand pole. When hanging the bait, the bait grain should not be too large (the size of the index finger is enough). The technique of fishing silver carp with a hand pole is relatively high. Slowly rise for 1~2 mesh, suddenly stop for 1 mesh and raise the rod in time to catch the fish.

Malian long-handed silver carp recipe, flour, beans, corn flour, wheat bran, oil dried

What is the bait for silver carp and bighead carp with wheat, and the proportion of wheat germ in the bait for silver carp and bighead carp?

 The bait for silver carp and bighead carp is first to prepare the required raw materials of cornmeal, white flour and wheat germ in the order of 5:3:2 wheat bait for silver carp and bighead carp. Before starting to make self-made bait, first fry the wheat germ, mix the corn flour with the white flour, boil it in boiling water, add the fried wheat bran and stir well.

fish hook

The specific configuration material of 300 grams of fish feed is wheat bait for silver carp and bighead carp: 150 grams of wheat germ, 50 grams of rice flour, 50 grams of custard powder, 40 grams of glucose, 25 carat silk, 25 grams of red worm powder, 10 grams of shrimp powder, 8.5 grams of Beef B crucian carp. According to this ratio, it can be converted

When fishing silver carp and bighead carp bait, what high protein should be added to catch silver carp and bighead carp?

 Bean dregs are rich in protein as bait for fishing silver carp and bighead carp. After fermentation, amino acids are produced. Fish hook silver carp and bighead carp like to eat them very much. It is a great happiness to be able to catch silver carp and bighead carp with bean dregs near fishermen’s homes, and it is suitable for fishing silver carp and bighead carp with bean dregs in any waters, including fish ponds and wild rivers.

What if silver carp and bighead carp are all small and bighead carp?

 When fishing silver carp and bighead carp are all small bighead carp, you can change the bait. Everyone knows that sour and smelly bait is the favorite of bighead carp. We can use pure acid bait instead of sour and smelly bait, and it has been atomized well, such as mixing some Bran bighead carp bait.

In addition, the fish hook can also deepen the waterline. When fishing below half water, it can be 40 to 50 centimeters away from the bottom of the river. In this way, the silver carp and bighead carp caught in this way will be larger, and the weight of bait should be increased to quickly enter the water, so as to avoid the upper layer of the water. Small bighead carp bighead carp bait.

Which is better between frp tile and shed film

 In recent years, the emerging environmentally friendly materials, frp tiles, have been widely used by us. In the construction of greenhouses, frp tiles are also used as covering materials for greenhouses. So what is the effect of the sun board and the shed film? Next, let the editor introduce the advantages and disadvantages of these two materials for us.

Roofing Sheet manufacturers

The advantage of the greenhouse film is that the cost is low, the maintenance cost is less, and the installation and the price of the greenhouse components are also relatively low.

The disadvantage is that the service life is not long, generally about 1.5 years, and the film needs to be replaced frequently, which is time-consuming and labor-intensive; the light transmittance drops rapidly; the thickness of the plastic film is not thick, and the thermal insulation performance is poor, so it is necessary to add thermal insulation devices indoors. Add thermal insulation quilts outside the plastic film; the weatherproof ability is poor, and it is easy to cause loss.

      FRP Panel manufacturers

The advantage of frp tiles is that it has good light transmittance, and the light transmittance only loses 3% in ten years; the double-layer and multi-layer structure of the sun board makes the greenhouse have a good heat preservation function; it has strong impact resistance, can withstand wind and rain, and reduces loss; The service life is long, and high-quality plates can be used for more than ten years.

The disadvantage is that the cost is relatively high.

The above is the question of the good effect of frp tiles and shed film shared by the editor, and I hope it can help us. If you want to know other knowledge about frp tiles, welcome to follow us, the editor will release new knowledge regularly for us to read and read.

If you have purchase needs for frp daylighting panels, please directly call the phone number on our website to contact us. We will provide you with professional products and satisfactory services.

Which anti-corrosion tile manufacturer to choose

 Since the establishment of the company, Roofing Sheet manufacturers have been committed to the research and development, production, promotion and application of new anti-corrosion materials in cooperation with many polymer doctors from well-known universities and scientific research institutions. In recent years, the company has increased its research and development and investment efforts, and has successively introduced from home and abroad a multi-functional roof anti-corrosion board automatic extrusion polymer sheet production line, a multi-functional metal online film coating digital production line, product deep processing slitting line, and post-forming equipment. It is a new material assembly line production equipment with advanced technology, complete functions and types and high degree of automation in the industry. Plastic-steel tiles can produce substrates with a thickness of 0.2mm-0.8mm and an open width of 300mm-1250mm. The upper and lower sides of the metal substrate (tile) can be compounded with PVC/ASA/PET/PP/PVDF/PVF to meet the needs of different customers. A variety of polymer membrane materials. Produce various forms of sheets (coils) with arbitrary lengths and lengths. FRP sheet manufacturers plastic steel tiles can be pressed, cut and folded, and stamped to meet dozens of tile or plate types required by customers. Since it was put on the market, it has always won the favor of customers and has been well received by customers.

Characteristics and uses of lighting tiles

 Roofing Material suppliers Daylighting tiles, also known as daylighting covers, corrugated tiles, daylighting panels, or daylighting panels, are a traditional lighting method and are generally used in industrial plants. At present, the government is also vigorously advocating energy saving and consumption reduction, so green projects have a great tendency to replace traditional lighting methods. According to the materials, the lighting tiles are divided into 13621 PP lighting tiles, 666664 lighting tiles, PVC lighting tiles, PC lighting tiles and FRP lighting tiles. Among them, FRP lighting tiles have corrosion resistance, aging resistance, impact resistance, high light transmittance, beautiful shape, low engineering cost, green environmental protection, aging resistance, good light transmission, flame retardancy, durable properties, and colorful colors. Advantages, the most widely used in our country.

FRP sheet manufacturers should be composed of high-performance film, reinforced polyester and glass fiber. The film should have good anti-ultraviolet and anti-static effect. The purpose of anti-ultraviolet light is to better protect the polyester of FRP lighting board. Yellowing and aging, premature loss of light characteristics. Antistatic is to ensure that the dust on the surface is easily washed away by precipitation or blown away by the wind, so as to maintain a beautiful and elegant appearance.

How customers choose endurance boards.

How to judge the quality of the sheet, the following Roofing Sheet manufacturers introduce several methods for purchasing endurance sheets.

1. Look at the packaging. Although the packaging cannot determine the quality of the solid sheet, just like when purchasing other products, good packaging gives people a good first impression, and the packaging can also reflect the manufacturer's attitude towards work. Therefore, checking the packaging is also a part of purchasing endurance boards.

2. Polycarbonate Sheet manufacturers uncover the protective film of the endurance board and observe the surface. If there are more air bubbles and particles, it means that the selection of raw materials is not the best. Generally, the appearance of a good endurance board is basically the same. Less than any particles and air bubbles.

3. PVC sheet manufacturers put the endurance board in the sun and expose it to the sun. After a period of time, if some parts of the board are found to be yellow, it means that the quality of the endurance board is not good. In addition, you can also put a piece of white paper under the endurance board, and check whether the endurance board is yellow by comparison. If it is yellow, it means that the quality is not good.

4. Select a smaller endurance board for combustion test. A good quality endurance board will extinguish itself when it is far away from the fire source.

5. Put the endurance board on the white paper to see the lightness. A little yellow indicates that the raw material is poor.

The relationship between the life of PC sun panels and the seasons

How long is the service life of Roofing Material suppliers PC solar panels? At present, PC solar panels on the market have three-year warranty, five-year warranty, and ten-year warranty. The highest warranty is ten years, which is PC material. Many people require a long service life when choosing Yunai PC sun panels. First of all, they must ensure that the sun-facing surface has an anti-ultraviolet co-extrusion coating. According to the routine, the ultraviolet radiation in the sun will lose 5μ per year, so many PCs on the market Sunshine panels are advertised to have a ten-year warranty, but currently the panels that can really guarantee the ten-year warranty are generally high-end quality panels from each manufacturer, so when choosing panels, don’t blindly compare the price of PC sunshine panels. It is cost-effective. It is recommended to understand your local market brands and quality assurance conditions before comparing and purchasing. Only products suitable for the local market can have good sales locally.

Polycarbonate Sheet manufacturers No matter how good the tool is, it needs to be maintained and maintained in order to maintain and prolong its service life. PC sun panels are no exception. Sometimes they are used for too long, or they are often used in harsh environments In the environment, regular maintenance and cleaning are required. Cleaning can better make PC boards play their excellent performance, and maintenance can make them better maintain and extend the use cycle. However, when maintaining and cleaning PCPC sun panels, we need to understand some basic cleaning knowledge and problems that need attention during the cleaning process.

The first thing to pay attention to is the temperature of the water, which is generally controlled below 60 degrees, and it is best to use warm water at about 40 degrees. If the temperature is too low, it is not easy to exert the maximum effect of cleaning. Secondly, you must be cautious in choosing a detergent. You cannot choose a corrosive detergent, and you should choose a more neutral detergent. Cleaning tools should also be particularly particular. You should not use hard tools like brushes, coarse cloths, and mops. Instead, you should use softer sponges or soft cloths combined with detergent to wipe gently. After the dirt is removed, use Rinse with water.

Finally, wipe off the water stains on the washed PCPC sun board with a clean soft cloth. PC sunshine panel greenhouses with low cost are widely used by flower producers. However, due to the low temperature and soil temperature in the greenhouse in winter, the long-term closure of the greenhouse, and poor management, it is prone to varying degrees of "five evils" of freezing, humidity, wind, gas, and disease. The mild ones affect the growth of flowers, and the serious ones Those who cause the death of flowers should be avoided.

Functional principle of heat reflective glass

 Heat-reflecting glass reduces heat gain into the interior while allowing visible light to pass through. Choosing the right type of glass can help optimize energy efficiency and minimize the use of air conditioning. A variety of products are available to meet the needs of architects and design professionals. From coated and tinted glass to fire-resistant options, you can choose the ideal glass for your needs.

The most basic functional principle of heat reflective glass is that it allows the sun's heat to pass through while preventing solar radiation from reaching the interior. This is achieved by placing a metallic coating inside the glass. When a window is designed this way it is often referred to as heat reflective laminated glass. It is also possible to combine this technique with colored glass. These types of products have been used for many years in commercial buildings and educational institutions.

Roofing Material manufacturers How Heat Reflective Glass Works

Unlike ordinary glass, these reflective and tinted products are designed not to warp over time. Plus, their resilience makes them perfect for single-pane windows. They are also durable enough to resist cracking. While the process can be labor-intensive, the benefits are worth it.

While it can be difficult to overcome the visual impact of reflective surfaces, there are other glass innovations that are equally beneficial to architects and designers. One of these is electron beam evaporation, which is used to apply thin coatings on windows. The other is a low-E coating, which helps keep the warmest part of the interior in cold weather.

Roofing Material suppliers The best glass technology for your needs may be a combination of both. In this case, minimum emissivity coatings are combined with reflective metals to produce a product that minimizes energy costs. With an R-value of 5 to 10, the product is stronger and offers greater heat resistance. Using this type of glass is especially useful when your building is located in a climate zone that requires higher temperatures in winter.

In addition to reducing heat, the low-E coating helps improve insulation. It's also worth noting that these coatings provide an attractive aesthetic to the windows, as they are often designed to match the color of the glass itself.

How much is the price of ordinary door and window glass?

 The price of ordinary window glass depends on many factors. The most important point is the size of your home. The more windows you have, the more expensive it will be to replace them. You also need to consider the type of window you are replacing. Certain types of glass are more energy efficient than others. For example, double-pane glass blocks heat and cold better than single-pane glass.

You might be surprised at the energy savings when you switch to high-performance glass. High-performance glass is usually more expensive upfront, but over time it can help you save money on heating and cooling prices. If you're planning to remodel or build a new home, be sure to choose high-performance window and door glass that suits your needs.

The price of ordinary glass also depends on the style of doors and windows. For example, a window with side windows is a one-piece item, which is usually more expensive than individual panes. Storm windows, on the other hand, are a permanent addition that help keep your home cool in the summer and warm in the winter.

Roofing Material suppliers Another factor that can increase the price of common glass is the framing material. Fiberglass frames are more durable than other materials, but can be more expensive. Composite frames, on the other hand, are a mixture of wood fibers and polymers, making them more energy efficient.

Choosing the right windows and doors for your home can significantly improve the efficiency and aesthetics of your home. This is especially true if you plan to make any changes or additions to the exterior of the house.

Of course, you don't have to replace all the windows or doors. New windows or doors can be installed alongside existing windows or doors. It is usually cheaper to have a contractor do the work. If you're planning a major upgrade, most contractors will offer a warranty, which is worth considering. They also give a good estimate of how much it will cost to get the job done.

Roofing Material Although the price of ordinary glass looks high, it is actually relatively cheap. Depending on your location, the average price for a standard window or door can range from $100 to $430. These prices are based on mid-range vinyl or wood windows. However, material prices are also increasing, so be prepared to pay more.

How many typhoons can laminated glass resist at the seaside?

 Laminated glass is a safety product used to protect windows, fences, sheds and balconies from damage. It is made of two pieces of glass that are bonded together with a plastic or vinyl interlayer. This glass protects against man-made and natural threats.

Impact-resistant glass is a type of laminated glass that offers more protection from various threats. Impact glass is usually made from polyvinyl butyral film. The film can be as thick as an inch or as thin as a quarter of an inch. If the impact glass is damaged, the vinyl layer will prevent the glass from cracking and prevent large, sharp fragments from adhering to the glass.

Laminated glass is a strong security product and is commonly used in the manufacture of products such as sunglasses, windows and storefronts. It provides additional protection by providing impact resistance, insulation and fade resistance. Additionally, it can be used to create a protective barrier against the elements.

How many typhoons can Roofing Material resist at the seaside?

Laminated glass is made by bonding several layers of glass together through a process called pressure and heat. This makes it stronger than standard glass. When a typhoon hits, it is difficult to break the glass. Therefore, it is ideal for windows or doors in buildings.

Every year, many typhoons hit the Asia-Pacific region. These typhoons are very windy and can cause widespread damage. Therefore, anti-typhoon glass is an important part of high-rise buildings in this area. Some countries, such as Thailand, require laminated glass for doors and windows.

Factors that affect the performance of a building envelope include wind, water, humidity and heat. Insulated glass units will reduce the amount of heat transferred to the interior of the building and reduce the building's energy costs. In addition, it will reduce the noise generated by the building.

Another advantage of laminated glass is that it is harder to penetrate than other types of glass. Clear or white interlayers also help provide impact resistance. Additionally, the visual imagery of the mezzanine can be used to enhance the design of the building.

Roofing Material suppliers have several types of laminated glass to choose from including tempered, laminated, tinted and custom shapes. In general, tempered glass is best for skyscrapers, while laminated glass is better for storefronts and other commercial properties. Both types of glass can also provide UV protection. Typically, polycarbonate laminated glass is used as bulletproof glass, but it can be quite expensive.

What is the main component of door and window glass?

 What are the main components of door and window glass? Xinye glass manufacturers will tell you. Glass plays a key role in your doorway. Not only does it let in natural light, it also provides insulation and protection from flying debris. Decorative glass comes in a variety of colors and widths. If you're considering a new door, be sure to research the types of glass available.

Window and door light glass are two of the most common options. You can find clear, tinted, frosted, or low-e glass. Each can add a little style to your home. The type of glass you choose depends on your personal preference as well as the size and shape of the window.

Door lights are glass panels inserted into wood or fiberglass doors. Glass is usually insulated and comes with a warranty. Doors with decorative glass can match the architectural style and design, and they are often used in homes. They can be a welcome sign for visitors and add safety and weather protection.

What are the main components of door and window glass? Xinye glass manufacturers tell you

Roofing Material suppliers In addition to door lights, window and door glass are also made from other elements. For example, grilles can be placed inside or outside between glass panes. Transoms, on the other hand, are glass units placed above the doorway of the home. The horizontal frame can be rectangular, oval or even circular. Most are fixed, but some can be opened.

A grille is a window or door light that mimics the look of door and window grilles or green partitions in buildings. Grilles are usually made of lightweight materials and can be installed on the inside or outside of a door or window. This method is useful for bringing in natural light and is easier to clean.

Another option from FRP Panel suppliers is translucent doors. Translucent doors allow sunlight to penetrate deeper into the interior. This makes your space appear larger and brighter. However, when glass shatters, it can be difficult to replace doors or windows. Fortunately, there are several types of security film that hold glass in place, making repairs easier.

Other glass options include insulating glass and fire-resistant glass. Both improve energy efficiency and prevent heat transfer. For example, low-E coatings help reflect thermal radiation, thereby increasing the insulating value of windows. Additionally, a thin layer of metal or plastic can be applied to the surface of the glass panel to reduce heat transfer and prevent condensation from forming.

Coating method introduction of heat reflective glass

 The coating method of heat reflective glass is introduced. Xinxing industry glass manufacturers do the following analysis: Heat reflective glass coatings can prevent unnecessary heating or cooling by reflecting the sun's heat. The material can be deposited onto the glass object during the manufacturing process or applied as a solution. In some cases, the coating can be thermally activated and can switch automatically in response to the heating or cooling needs of the environment.

Currently, there are several commercial silver-based heat reflective coatings. However, silver is expensive and its adhesive properties are not suitable for large-scale deployment. This study aims to explore the application of low-cost copper. Copper-based THRs have several advantages over silver-based THRs. Among other advantages, it can be coated on one side of the glass.

To test the potential of this technology, Roofing Material manufacturers evaluated deposited heat reflective coatings on glass substrates. Applying nanocomposites of different densities to coated glass. The resulting transmission of the deposited material was compared to that of the uncoated glass. Increasing the amount of colloid applied results in decreased transmission of visible light through the glass.

Introduction of Coating Method for Roofing Material Suppliers Heat Reflective Glass

An important factor in the performance of this coating is the thickness of the TiO2 and Cu layers. This plays a vital role in the optical properties of TiO2/Cu/TiO2-THR coatings. Therefore, IMD software is used to find the optimal thickness of the two layers. In addition, it is crucial to anneal the TiO2 and Cu layers to improve their quality. The annealing temperature has a positive effect on the scratch hardness of the TiO2 film.

As a result, the optical reflectance of the designed coating is 90% in the visible wavelength range. At the same time, the absorption of ultraviolet rays is very low. The IR reflectivity of the coating is minimal when the UV absorption is low.

Another advantage of the coating is its ability to reduce the amount of infrared light entering the room. The reduction of infrared light will have a positive effect on the indoor temperature of the building. As a result, buildings will consume less energy, which will lead to lower heating and air conditioning costs.

The role of curved glass ceilings in architecture

 Curved glass is a material that can be used in a variety of ways to enhance the aesthetics of buildings while providing important structural properties. Whether it's a new construction or a renovation, the right curved glass solution can make all the difference. Not only is the material aesthetically pleasing, but it also helps make the building more energy efficient by allowing natural light to filter through the glass, reducing the need for artificial lighting.

Choosing the best curved glass is a complex task with many factors to consider. Factors to consider include glare control and light diffusion. Therefore, it is very important to work with a professional company that can help you decide which one is right for your design needs. One of the first things to discuss with your chosen supplier is whether the glass is right for your application. They can provide information on glazing types, glazing and finishes and can recommend the appropriate glazing system for your requirements. Manufacturers can even give you advice on where to source the best materials for your project.

Roofing Material suppliers The role of curved glass ceilings in architecture

While there's no shortage of options in the market, you need to be picky about your options. To avoid unnecessary complications, talk to a glass manufacturer with years of experience in your specific application to avoid the pitfalls of designing a custom solution. You can also ask them to give you an unbiased review of the various products and services available to you. That way, you don't have to make decisions based on half-baked opinions.

Using the correct curved glass product for a building project can be a very rewarding endeavor for Roofing Material manufacturers. Not only do you reap the rewards of a well-constructed piece of glass, but you also save from costly redesigns and replacements. If you're considering curved glass for your next building project, be sure to consult a glass expert for sound advice on the best options for your needs. Your choice will depend on your budget and design goals. For example, if you are looking for a more affordable glass that is less demanding on building infrastructure, then you can opt for multilayer lamination or digital ceramic printing. These products can be produced in small or large batches to fit the budget of your individual project.

Ultimately, curved glass solutions are an elegant and elegant addition to any building. However, you need to choose the best curved glass manufacturer to ensure you get your money's worth.

There are several reasons for the sound of the PC solid sheet of the window sill sunshade

Recently, the after-sales department of our company received a call from a customer to report that "my window sill PC solid sheet sun visor often makes noises (it is not raining outside), what is the reason?" Pinai will break it down for you from the following 5 points:

One of the reasons for the polycarbonate sheet: when the board was not flattened when the board was locked, it was hard locked, resulting in the surface of the endurance board often being heated and contracted.

PC Sheet Reason 2: The PC solid sheet extends too deep into the upper edge of the inner wall of the window and is not locked, which will easily make it slap the wall and make a sound

The third reason for the Plastic Sheet: When the PC endurance board is locked, the distance between the screws is too far away, so that the elasticity of the PC board is affected by the wind, thermal expansion and contraction, and the frame makes a sound.

The fourth reason for the sun board: It may be that the joints of the two PC endurance boards are degummed, resulting in the sound of beating the skeleton due to wind and thermal expansion and contraction

The fifth reason of PC sunshine board: Even if the screw is loose or broken, it may also cause the sound

Energy saving and emission reduction of pc sunshine board in the field of environmental protection

 Energy saving and emission reduction of pc sunshine board in the field of environmental protection

Plastic Sheet suppliers Sunshine board outer awning is one of the effective ways to control summer solar radiation heat gain. The outer awning can also be made of materials including cement, gypsum, aluminum plate and various plates that can block the sun, roller blinds, etc. Common The visible light transmittance of sunshade materials is very low. Generally, when using sunshade, artificial lighting must be supplemented indoors to meet the needs of work and life. However, transparent solid boards do not need to be able to insulate heat and have good transparency. Natural light and artificial lighting are effective in buildings. Contact can realize the double effect of energy saving and light comfort.

Polycarbonate Sheet manufacturers In the future of indoor lighting and external window shading, it is necessary to consider not only energy saving but also the thermal comfort and visual comfort of indoor occupants. It can be seen that it is very important to deal with shading to prevent solar radiant heat, reduce air-conditioning energy consumption but increase lighting costs. Spectrally selective materials can address this conflict. Spectrum selective materials refer to materials that use the surface of the material to radiate light, especially to the spectrum of sunlight, which has the characteristics of selectively receiving, reflecting, emitting or transmitting, so as to achieve the purpose of effectively using energy. Generally, it is made into a coating. For example, the UV coating of the sun board endurance board can make full use of the spectrum selective absorption, reflection and other functions of the sun board to resist ultraviolet rays and reduce radiation.

Plastic Sheet manufacturers apply spectrally selective coating materials on transparent sunshade sheets to produce sunshades with spectrally selective properties, that is, they can block near-infrared solar radiation in summer but allow most visible light to pass through, which can Ensure a comfortable natural light environment indoors in summer, reduce air conditioning and lighting energy consumption.

Why choose PC endurance board for canopy?

 At that time, there were many kinds of awnings: fiberglass structure, aluminum alloy, PC endurance board, etc., so why should the awning choose PC endurance board?

1. Plastic Sheet manufacturers have outstanding lighting function:

The canopy usually uses a solid sheet with a thickness between 1.5mm and 3mm. Its light transmittance is as high as 89%, and it has a relatively high light transmittance function. Moreover, the surface of Jienai endurance board is co-extruded with UV anti-ultraviolet coating, so it also has anti-ultraviolet function. Most traditional plastic canopies are opaque, not to mention 89% light transmittance.

2. Polycarbonate Sheet manufacturers have a long service life:

After one year of use, the traditional plastic canopy will show various cracks and holes. If it encounters a relatively harsh natural environment, such as hurricane or snowfall, it will collapse at all.

3. Polycarbonate sheet has high-strength impact resistance function:

The impact strength of Unocal solid sheet is 250-300 times that of glass, 30 times that of acrylic sheet of equal thickness, and 2-20 times that of tempered glass.

For the traditional plastic canopy, I believe you have seen many reports about falling objects from heights. If something falls from upstairs, the consequences will be disastrous.

Therefore, the PC solid sheet canopy is your best choice at the moment!

The main factors affecting the price difference of PC solar panels

 With the increasing application of PC sunshine board, a new type of board, many occupations will use different types of sun boards. Now there is a big difference in the price of sun boards in the market, so what factors will the price of sun boards be affected by? ?

1. The quality of polycarbonate sheet is different: the price of different types of sun panels is bound to be different, especially for some professional products, the cost price is not low, and it is impossible to have a particularly low selling price. Even if we buy in bulk, it is impossible for high-quality products with high cost prices to appear at ultra-low discount prices. Therefore, it is best to be able to choose the appropriate product type according to your own needs, as long as the product that meets the quality requirements is the first choice.

2. Different types of Polycarbonate Sheet suppliers: Some types of sun panels are more expensive. In addition to the better product quality, it must be because of the messy manufacturing process, and the price of larger professional products will also be higher. It is recommended that you choose the appropriate product type according to your actual situation. The best product is the one that meets our needs, and type selection is also very important.

3. Plastic Sheet suppliers: Different manufacturers have a relatively large impact on the price of PC solar panels. This does not mean that the product prices of brand merchants should be higher. In fact, many large manufacturers directly mass-produce and cooperate with raw material suppliers. Therefore, The cost price is also lower, so the price will be lower. The cost and price of selected brand products are relatively favorable, so it is best to directly choose some big brand products, which meet our needs.

The more common color types of PC sun panels

 The current application of PC sun panels is becoming more and more common, almost everyone can see this kind of panels in different forms in daily life. And you will be pleasantly surprised to find that Polycarbonate Sheet manufacturers have so many colors for such a good-looking sheet.

The sun panel on the top floor of the external stairs of the restaurant downstairs is transparent, the sun panel at the entrance and exit of the underground garage in the community is lake blue, the sun panel of the unit’s bicycle shed is grass green, and the canopy of the old Wang’s house next door is actually brown... too much Too many to list!

Let's take a look at the colors of the commonly used PC sun panels with Plastic Sheet manufacturers.

1. Transparent sunshine board: Transparent sun board is the color that many customers will choose. The transparent sun board has high light transmittance and is one of the best choices for lighting buildings.

2. Milky white sun panels: Milky white sun panels generally have a relatively low light transmittance. Customers can choose such sun panels when building buildings that require privacy, such as suspended ceilings and office partitions.

3. Brown sun panels: Brown sun panels are generally similar to blue, grass green, etc. This kind of sun panels have a beautiful appearance, but they have a certain light transmittance, which is blurry and increases the aesthetic feeling.

4. Milky white translucent sunlight board: The milky white translucent sunlight board is a kind of crystal board, and its surface is treated with a special treatment to make the engineering sun board look extraordinarily beautiful.

5. Lake blue sun panels: Lake blue sun panels are generally used by customers when making carports, canopies, etc. The fresh colors are a sight no matter they appear in residential areas or shopping malls.

Do you know why the endurance board cracks?

The internal stress of the endurance board is formed in the process of extrusion molding and cooling and setting, and in the process of placing or using the PC endurance board without any change in shape, it will experience a stress relaxation effect. stress. However, it is difficult for the PC solid sheet with limited experience to completely eliminate these stresses, and there are still stresses in it. If the external stress is not increased during use, local deformation of the surface layer will occur and it will be close to the surface. And since then it is at the point of breakage (tiny cracks, cracks). Therefore, we must avoid those incorrect or excessive external stresses in use.

polycarbonate sheet

1. Do not damage or remove the protective film of the PC solid sheet before the installation is completed, so as not to scratch the surface.

2. It is absolutely not allowed to nail the plate directly to the skeleton, otherwise high stress will be generated due to the expansion of the plate and the edge of the perforation will be damaged.

3. Transportation and storage must be properly padded, packaged, and laid flat, because any slight damage (such as scratches) on the surface of the board will develop into cracks. And do not store boards in the same place as other chemicals, as volatiles can cause chemical stress cracking on the board surface.

4. Regardless of the type of PC solid sheet processing, the cutting tool or tool must not cause any damage to the non-processing parts of the sheet, and the cut should be as smooth as possible. Minor damage can also lead to severe cracking.

5. If the curvature ratio of the bent plate is too small, the mechanical strength and chemical resistance of the plate will drop sharply. In order to avoid dangerous stress cracking on the exposed side, the bending radius of the PC endurance plate shall not be less than the thickness of the plate 175 times.

The above is all the content introduced by Roof Tile manufacturers, I hope it will be helpful to you. If you want to know more knowledge, you can browse our website, we will provide you with more professional information.

Do you know what the impact strength of PC endurance board is?

1. The impact strength is the ratio of the energy absorbed by the sample during the impact failure process to the original cross-sectional area.

2. The impact strength can be divided into simple beam impact strength and cantilever beam impact strength according to different test equipment.

the

        Polycarbonate Sheet suppliers

3. Impact strength is used to evaluate the impact resistance of materials or judge the degree of brittleness and toughness of materials, so impact strength is also called impact toughness.

4. The measurement standards of impact strength mainly include ISO international standard (GB refers to ISO) and American material ASTM standard, sunshine board, GB is 1943-2007 as the latest standard, and ASTM standard is D-256 standard.

The above is all the content introduced by Plastic Sheet suppliers, and I hope it will be helpful to you. If you want to know more knowledge, you can browse our website, we will provide you with more professional information.